Want to use peptides for mass gain and fat burning? Then be sure to read the detailed instructions on how to properly dilute and inject these drugs. We will assume that you have already decided on the choice of peptides and purchased them. Now we will tell you how to prick peptides and what you need to use these drugs. In addition to the peptides themselves, you must purchase insulin syringes and diluent. As the latter, you can use bactericidal water or water for injection. Most athletes prefer the first solvent, but if you have not been able to buy one, then water for injection is fine. You can buy these solvents at a regular pharmacy.
Syringes should have a capacity of 100 (1 milliliter) or 50 (0.5 milliliter) units. The manufacturer of the syringes is not critical, although athletes often recommend BD products. This is due to the fact that these syringes inject all the solution contained in them without residue. Often, a small portion of the drug remains in the syringe.
It should also be recalled that if the skin is very delicate, then the introduction of any injectable drug is accompanied by quite strong pain. To minimize them, it is best to use novocaine or icecaine as a solvent for peptides. These are pain relievers that will make the process of administering the drug softer. Here again it is worth returning to BD and its products. Many athletes say that the needles from these syringes are as thin as possible, which also facilitates the administration of peptides.
How to calculate the correct dosage of peptide?
Most often, peptides are used in amounts of one to three micrograms per kilogram of the athlete's body weight. For example, with a weight of 100 kilograms, then the maximum one-time dosage would be 300 micrograms. However, this is true if the peptide is used solo.
Most courses of drugs involve creating a synergistic effect from a combination of peptides, which allows you to reduce the dose to two micrograms for every kilogram of your body weight.
The correct calculation of the dosage is no less important in comparison with the knowledge of how to inject peptides. As an example, we will choose GHRP 2, one bottle of which contains five milligrams of the active ingredient. The algorithm for your actions will be as follows:
- Add 2 milliliters of a solvent, such as bactericidal water, to the bottle.
- We make a proportion of 2 milliliters = 5 micrograms, after which we can bring these units to the following form - 200 units = 5000 micrograms.
- One 100-unit syringe can contain one milliliter of solution.
- Solving the proportion made in the third paragraph, we get that one unit of syringe volume corresponds to 25 micrograms.
After all these simple calculations, we get that 100 micrograms of the peptide solution corresponds to 4 units, which must be poured into the syringe.
The most popular among builders are GHRP 2 and 6, which contain 5 milligrams of the active ingredient in one bottle. At the same time, there are peptides that are packaged by manufacturers and in two milligrams. The calculation algorithm will be similar to the previous one. But we'll make it a little easier for you and tell you that, say, 300 micrograms of Frag hgh 176-191 equals 30 volume units of an insulin syringe. Before starting to use peptides, study the syringe scale so that you do not make a mistake later.
How to inject a peptide?
It is necessary to inject drugs into the fat fold of the abdomen, although some peptides are more efficiently injected into the target muscles before starting training. This will allow you to accelerate local muscle mass growth. Many people are afraid of injections and this is the main reason for their refusal to use peptides.
You should remember that insulin syringes have significantly smaller needles than conventional syringes. So the diameter of the needle of an insulin syringe is four times smaller than the usual one. The situation is similar with the length of the needle, which in an insulin syringe does not exceed one centimeter. Let's take a closer look at the question of how to prick peptides. First, you should take the belly fat in your hand. Bring the syringe to it and insert it at a 45-degree angle. Start pushing the piston and do it slowly. When all of the solution has been injected, remove the syringe from the fold.
Very often, athletes are interested in where peptides can be injected besides the abdomen. The drugs can be administered subcutaneously or intramuscularly. We have just described the first method of introduction. Intramuscular injections are quite painful and, given the frequency of injections when using peptides, few people will be able to withstand it throughout the course.
Subcutaneous injections of peptides seem to be the simplest solution to the problem. Although after using an insulin syringe, the injection site heals quite quickly, try to constantly change the area of peptide injection. To do this, divide the belly into nine parts and change the injection sites.
How to dilute and prick peptides, see this video:
