We create decorative trees with our own hands - a master class

Table of contents:

We create decorative trees with our own hands - a master class
We create decorative trees with our own hands - a master class
Anonim

Do-it-yourself decorative trees will allow you to decorate a summer cottage or apartment. By remembering how to make a bonsai, you can easily create it. You can create many interesting things for the garden or home with your own hands from unnecessary materials. Small potted trees will be a worthy decoration for outdoor or home interiors.

DIY decorative tree - master class

Homemade decorative poplar
Homemade decorative poplar

Such a poplar tree is quite possible to put on the street, it is not afraid of the bright rays of the sun and atmospheric precipitation.

To make it, prepare:

  • green plastic bottle;
  • thick and thin wire;
  • a candle;
  • scissors;
  • a needle;
  • cement or gypsum;
  • glue;
  • pot;
  • matches;
  • green and gray threads.

From the large wire, using pliers, separate three identical segments that need to be connected to each other by twisting. Wrap the ends of these blanks on one side.

Wood base wire
Wood base wire

Dissolve cement or gypsum, pour the mortar into a pot, place the tree trunk with curved ends in a container. While the mass hardens, it is necessary for the poplar tree to acquire branches. To make leaves for them, cut into squares of various sizes, cut leaves out of them. Heating the needle over the flame, make a hole in the upper part of the hole.

Tree leaves
Tree leaves

Insert a thin wire here, fold in half, twist. Combine three branches into one, make several such blanks.

Branches blanks
Branches blanks

To make further a decorative tree with your own hands, connect several blanks consisting of three branches.

Forming a branch from several blanks
Forming a branch from several blanks

Close the wire parts with gray thread, secure the ends with glue. Leave the bottom of the branch free, it will need to be attached to the trunk.

Attaching a branch to the base
Attaching a branch to the base

In the same technique, complete the entire tree, wrap its trunk with gray thread.

Finished tree
Finished tree

To make the grass, cut the green threads to the same size, fold them in half. Lubricate the folds with glue, attach the blanks to a plaster or cement base.

Ready-made poplar in a pot
Ready-made poplar in a pot

This is how the poplar tree turned out to be so wonderful. If you want to make a whole mini-garden, then check out the second master class.

How is a homemade apple tree made with your own hands?

Home apple tree
Home apple tree

Such a decorative tree is suitable for enclosed spaces, since its flowers are made of yarn.

To do it, take:

  • wire;
  • green and brown fabric;
  • cardboard;
  • pencil;
  • scissors;
  • nippers;
  • Scotch;
  • glue;
  • pot;
  • gypsum or cement;
  • hook;
  • the threads are brown and red.

Using a piece, cut 6 pieces of wire of 30 cm, 5 of 25 and 22 of 4 cm.

Wire for wood
Wire for wood

Armed with scotch tape, use it to attach three small ones to one large branch. Form several of these blanks.

Forming wire blanks
Forming wire blanks

At the next stage, the branches need to be wrapped in a cloth. Fleece or velvet looks especially beautiful, use these fabrics. From the selected brown fabric, you need to cut strips, their width is 2 cm. Wrap the newly created blank branches with them, leave 3 cm free at the bottom. Fix the ends of the fabrics with glue.

Wire branch
Wire branch

In this technique, arrange several blanks. Now they need to be collected into a single tree. To do this, you need to cut off a strip 3 cm wide from the fabric, wrap it around the canvas and the connected branches. Secure the ends of the fabric with glue.

Branched part of the tree
Branched part of the tree

To make the decorative tree further, you need to place it in the container of your choice. If it does not have a narrow neck, pour gypsum or cement mortar into the container to fix the plant. Spread the branches and you can start decorating them.

Ready wood base
Ready wood base

Now you need to cut leaves of different sizes from green fabric. To prevent their edges from spreading, rinse these blanks over the flame, without bringing them too close to it.

Apple tree leaves
Apple tree leaves

Glue the leaves to the twigs, and you can start creating fruits. We will make them from pompons. Cut out two circles with a diameter of 3 cm from the cardboard. Draw a smaller circle inside, cut it out. You will get two of these cardboard rings.

Basis for making apples
Basis for making apples

Connect them into one piece, wind a red thread around it, using a crochet hook. The yarn should completely cover the workpiece. Now you need to cut it along the outer edge, lay a brown thread, use it to tighten the resulting pompom.

Making an apple step by step
Making an apple step by step

Cut out the leaves from a green fabric, glue them on a brown thread.

Ready apple
Ready apple

Hang the fruit on the twigs. You can decorate the pot as you like.

If you still want to make a decorative tree for the street, then the following option will suit us.

Christmas tree do it yourself

To create it, you need a small set of necessary things, these are:

  • thin and thick wire;
  • woolen green threads;
  • gypsum;
  • lighter;
  • candle;
  • glue;
  • scissors;
  • green plastic bottles;
  • cotton wool;
  • capacity;
  • Christmas decorations;
  • artificial snow.

Take 3-4 thick wires, twist the trunk out of them, bend the lower part so that this part is stable in a container with plaster. Where do you put it.

Preparation of the base for the Christmas tree
Preparation of the base for the Christmas tree

While the plaster is hardening, make twigs to make an elegant Christmas tree. With your own hands, cut off the neck and bottom of the green plastic bottle. Using scissors, the remaining part of this container must be chopped into identical strips. Their long edges must be cut into a fringe.

Forming a fringe for a Christmas tree
Forming a fringe for a Christmas tree

Using a heated needle on the flame, make a small hole in the corner of this plastic blank. Put a thin wire in here, fold it in half and twist it. Do the same with the rest of the blanks.

Fastening the fringe to the base of the Christmas tree
Fastening the fringe to the base of the Christmas tree

Now, starting from this corner, roll the wire. In order for the turns of plastic to be fastened together, periodically bring the solid side of the workpiece to the candle flame.

Folding herringbone fringe under fire
Folding herringbone fringe under fire

It is necessary to close not the entire branch with such needles, but only its upper part. Do the same with the rest of the details.

Formation of a Christmas tree branch
Formation of a Christmas tree branch

You can melt the needles over a candle flame or leave them in their original form. The workpieces should be of different sizes.

Four branches of a Christmas tree
Four branches of a Christmas tree

The crown of the decorative tree will be the shortest. Attach it here with the free end of the wire.

Forming the crown of the Christmas tree
Forming the crown of the Christmas tree

Then there are branches of a slightly larger size.

Fastening branches to the base of the Christmas tree
Fastening branches to the base of the Christmas tree

So gradually collect the whole tree, then wrap its trunk with green thread, securing the ends with glue.

Ready-made homemade Christmas tree in a pot
Ready-made homemade Christmas tree in a pot

If you are making a Christmas tree for the New Year or in the middle of summer you want to remember this holiday, then decorate the pot with artificial snow, you can replace it with ordinary cotton wool. Leave the tree as it is or decorate it with toys.

Decorated homemade Christmas tree in a pot
Decorated homemade Christmas tree in a pot

Such a decorative tree looks great at any time of the year. If you still have green plastic bottles, you can make a second Christmas tree with your own hands according to a different principle.

This is how it will turn out.

Another option for a homemade decorative Christmas tree
Another option for a homemade decorative Christmas tree

Take:

  • dense polyethylene or green oilcloth;
  • satin ribbon;
  • Styrofoam;
  • a branch of a tree;
  • suitable capacity;
  • glue gun;
  • alabaster;
  • wire;
  • beads.

To make branches, you need to cut oilcloth or polyethylene into strips of 5 by 30 cm. Fold them in half and cut them with a fringe on one edge. When you unfold such a blank, these needles will be on both sides.

Christmas tree blank made of oilcloth
Christmas tree blank made of oilcloth

In total, you will need about 20-25 such tapes. To make these parts turn into twigs, wind each one around a piece of wire.

Details for the Christmas tree made of oilcloth
Details for the Christmas tree made of oilcloth

Roll a cone out of cardboard and fix the sheet in this position with a stapler, align the edges with scissors. Spread glue on one side of the branch, attach to the back of the top of the cardboard cone.

Christmas tree cone
Christmas tree cone

If the fixation of the branch is weak, then first wrap its end with threads, grease them with glue and attach to the cone.

Here's how the Christmas tree is done next. Put it in a suitable container with your own hands, pour alabaster or other quick-drying solution here. Hold in this position for a while so that the mass grabs. You can lean against a vertical support to free your hands.

When the tree is in place, cover the surface of the mortar with pieces of styrofoam, which will become snowdrifts by gluing this material.

The container can be decorated with twine, for example. It is also fixed with glue.

To get a decorative tree with needles, take blanks from film and wire. Wrapping them around the cone, fix the turns with glue.

Fastening the cone-base of the Christmas tree to the rack
Fastening the cone-base of the Christmas tree to the rack

When the entire surface of the cardboard is decorated in this way, you need to arrange a herringbone. To do this, cut the strips from a thin satin ribbon, tie them in the form of bows. To prevent the ends of these items from wiping, scorch them over a flame.

Decorating a Christmas tree with bows
Decorating a Christmas tree with bows

Wrap the Christmas tree with gold thread from top to bottom in a spiral, glue the bows. You can decorate the pot with beads and rejoice at what a wonderful DIY Christmas tree it has turned out.

Decorative bows for decorating the Christmas tree
Decorative bows for decorating the Christmas tree

If you want to get acquainted with another method that will tell you how to make a decorative coniferous tree with your own hands, then the third master class in this section is for you.

Finished Christmas tree made of fabric
Finished Christmas tree made of fabric

Very soon you will have such a tree. It is quite simple to make it with your own hands. The main thing is to have a simple set of materials and equipment, which consists of:

  • a green plastic bottle with a volume of 2 liters;
  • scotch tape;
  • album sheet;
  • scissors.

For such a tree, you don't even need glue, so your hands will remain clean. From the bottle, you need to cut off the neck together with the hangers, put an album sheet twisted in a cone into the upper hole.

Another version of the Christmas tree from a plastic bottle
Another version of the Christmas tree from a plastic bottle

From the rest of the container, you need to cut 9 blanks:

  • three pieces will be 4 by 6 cm in size;
  • the next three pieces are 7 by 8 cm;
  • three more blanks 5, 5 by 8 cm.
Base for a Christmas tree from a plastic bottle
Base for a Christmas tree from a plastic bottle

Now cut each such detail on one side into strips in the form of a fringe. Their width is 4 mm, they do not reach the top about 1 cm.

Blanks from a plastic bottle
Blanks from a plastic bottle

Now you need to twist all these strips using the blunt side of the blade. Press it firmly against the plastic and slide it up and down several times.

Cutting a fringe from a plastic bottle
Cutting a fringe from a plastic bottle

Now these "eyelashes" need to be attached to the trunk.

Attachment of cilia to the trunk
Attachment of cilia to the trunk

Attach the largest ones down with adhesive tape, the smallest should be at the top.

Step-by-step creation of a Christmas tree from a plastic bottle
Step-by-step creation of a Christmas tree from a plastic bottle

Twist one smaller piece into a fountain and insert it into the top of the paper cone.

Forming the top of a Christmas tree from a plastic bottle
Forming the top of a Christmas tree from a plastic bottle

If you want to make a tree for the street, then use plastic instead of cardboard. Here is such a wonderful Christmas tree, created by hand, it turns out.

Ready-made Christmas tree from a plastic bottle
Ready-made Christmas tree from a plastic bottle

How to make bonsai?

Such a decorative tree can also be made from the most unexpected materials.

Ornamental bonsai tree
Ornamental bonsai tree

To create such a craft, you will need:

  • tracing paper;
  • pencil;
  • wire;
  • support for flowers;
  • Styrofoam;
  • aluminium foil;
  • dye;
  • brushes;
  • green paper;
  • scissors;
  • hot glue or liquid nails;
  • newspapers;
  • gypsum;
  • the cloth;
  • PVA glue.

First, you need to take a piece of wire that will be 2 times larger than the future tree. It needs to be folded in half, make a loop at the bottom. You need to make two holes in the stand. If it's plastic, use a hot nail or scissors to make them. If the material is denser, then put a block of styrofoam on the bottom of the container, wrap the wire around it.

Bonsai base
Bonsai base

By folding these two ends of the wire at the top, you will form the trunk. And bend it several times in different directions. Make branches out of wire, screw them to the base of the tree.

Forming a bonsai tree from a wire
Forming a bonsai tree from a wire

You will make smaller branches from thin wire, also screwing it into place.

Formation of small twigs from fine wire
Formation of small twigs from fine wire

Now wrap the foil tightly around the tree and its thicker branches. Then coat this blank with brown paint. Use a dry brush to brush over it to make the bark as realistic as possible.

Painted Foil Wood Pillar
Painted Foil Wood Pillar

Cut the leaves from a green cloth, attach a piece of wire to each with liquid nails or hot glue. Now it will be easy to attach the leaves to the twigs. Cover the sheets with green paint if desired.

Making leaves from fabric
Making leaves from fabric

To fix the decorative tree in the container, pour alabaster or gypsum here. You can put this solution only on the bottom of the pallet, and place crumpled newspapers on top. They are also covered with a small amount of plaster. You can decorate the surface of the pot with green shavings or paint this shade.

Here's how to make bonsai using old buttons. Such an original tree will become an interesting decoration of the room.

Bonsai decorated with old buttons
Bonsai decorated with old buttons

Twist the pieces of wire.

For creativity, you only need three names of objects:

  • wire;
  • coil;
  • buttons.

Twist the wire into a tree so that it has a trunk and branches. If the wire is not the right color, paint it or wrap it with dark thread. Put buttons on the tops of the wire sections, fasten them. Shape the tree and be glad that you now know how to make a bonsai from whatever is at hand.

Small denomination coins can be used instead of buttons. Using a thin drill, drills make holes in them, and then string them on the branches.

Bonsai decorated with coins
Bonsai decorated with coins

You can make such decorative trees with your own hands. If you want to see the process of making such products, then we suggest you sit comfortably in an armchair or on a chair to contemplate the video.

If you are interested in the process of creating a bansai, then check it out again. But the idea of manufacturing is a little different, as you will now see.

Recommended: