Interesting homemade products for giving are waiting for you in this article. You will learn how to make a lawn mower from an old washing machine, make a sink, a country shower, a dryer from scrap materials. Inquisitive minds often come up with various useful life hacks. Homemade products for the dacha, which were invented by the domestic Kulibins, will help to facilitate suburban work.
Useful homemade products for giving - do it yourself washing
Not everyone has the financial opportunity to buy a car "Karcher". If you can't get it, then why not invent it? A homemade car wash will eliminate the need for running water, reduce water consumption and thoroughly wash your car, fence, garden path, or other items.
Here's what you need for such a homemade product for a summer residence:
- plastic canister with a capacity of 5–20 liters;
- set of hose connectors;
- automobile nipple;
- a piece of hose;
- silicone sealant;
- sharp knife;
- compressor or car pump;
- watering gun.
Take a hose nozzle kit that includes 2 connectors, 3/4 threaded nipple, 1/2 reducer.
Here is the principle of operation of such a homemade product for a summer residence: you connect the gun to the hose, attach this device to the bottom of the canister. A nipple will be built into its neck.
Fill the container with water, but not to the top. Then screw the cap back on and pump air in. This will create pressure and water will run well when you pull the trigger of the gun. Here's how to assemble such a mini-sink.
Carefully cut a hole in the cover with the tip of a knife. It should be slightly less than the diameter of the nipple stem. Also cut a circle of the correct diameter at the bottom of the side of the canister.
Insert the nipple into the cover.
Now, helping yourself with the wire, put the sleeve in the hole provided for it. Apply silicone sealant to secure the junction of the sleeve to the canister.
It is necessary to tighten the lid and perform the rest of the work only after the sealant has completely solidified. Then you connect one end of the hose to the water gun and the other to the canister.
Pour water into a container, but not to the top, so that there is room for pumping air. But do not pump too much so that the canister does not deform or burst under pressure. See how the union should be screwed in and the connectors installed.
If everything is done correctly, then when you pull the trigger of the water pistol, the water will gush with a good stream. You can adjust the pressure by twisting the tip of the gun.
At the dacha, you can hardly do without a shower. Try to make an unusual, and tropical, then you can enjoy even more water treatments.
How to make a rain shower from scrap materials for a summer residence?
If you have just recently purchased a plot and you do not yet have a washing room, then you can take a shower right on the street, fencing a small area near the fence with a curtain. To make such a rain shower, very few components are required, these are:
- bracket;
- wire;
- flexible hose;
- metal beer can;
- hose adapter;
- awl;
- nails.
Nail the metal bracket onto the wooden fence to make the fixture at the correct height. Screw the adapter to the end of the hose, fix it on the slots of the beer can. The junction can be treated with a sealant. Use an awl to make many small punctures in the jar.
Wire the top of the hose to the bracket and attach the other end to the water supply or pump. When you lower the pump into a barrel of heated water, you will be able to enjoy a pleasant water treatment.
You can also make a rain shower head using a disc container as it. In its center, you need to fix a plastic adapter that is attached to the shower hose, and the central axis of the discs must be removed. Use an awl to make holes at the top of the cover. Glue all fasteners well with sealant. Such a nozzle is held on a bracket using a thick wire or on a rigid pipe.
If you have a desire to make a rain shower, then you can use plastic pipes for this.
You need to supply water to them, first make many small holes with a soldering iron, and then enjoy the pouring drops. Children like such water procedures.
But do not forget to first check the water in the container from which it will be poured into the shower, it should warm up in the sun.
And to make a stationary shower, you must first pour water into a tank or a barrel, which will be located under the roof or on the roof of the building. On a warm summer day, the water warms up well here, and you can wash yourself in plenty. To be able to do this even in cooler weather, then it is necessary to provide a heating system in such containers.
Dacha shower with your own hands
Before installing it, you need to make a shower stall. If possible, you can craft it out of wood by placing this small structure on the base. Add a wooden door or use a shower curtain like this.
There are also simpler options. If you have oilcloth fabric, then use it.
Banners remain after the end of promotions. You can contact an advertising agency and buy one for almost nothing. Another option is to purchase an impregnated fabric or use an old awning or tent.
If you made a fence from corrugated board and you still have materials, then try to make a shower for giving out of them. Metal pipes need to be dug in according to the markings, filled with concrete. When it dries, cut sheets of corrugated board are welded to the racks. One of them will become a roof.
If you have few wooden planks, then implement the option shown in the next photo on the right. And on the left is a shower, which is made like a wattle fence. So the materials for him will cost almost free.
When the shower is ready, you can install a water container on it. To make it warm better, you can make a kind of coil from metal or from a hose. Then the water will warm up more actively.
These and other homemade products for summer cottages allow you to make the most of the available containers.
To be able to receive warm water even when it is not heated by the sun, use electric heating. To do this, you can position the plastic barrel vertically or horizontally. Then it will be necessary to mount ten on one side, and on the other? water bay fitting. Make an overflow hole so that excess liquid flows out and you can see that the container is already full.
Now it remains to install the tank. Usually a shower roof is used for this. You can put a flat tank here, made of iron or plastic. You can also make a soul canister from a metal or iron barrel. If you need to heat the water, then a heating element is mounted in the barrel.
Check out other examples of what you can do on your garden plot with your own hands.
Interesting homemade products for giving with your own hands
Gardening tools are essential for working on the ground. Often, the store does not sell very high-quality sets. After a short time use, the handle of the shovel breaks off, or the teeth of the hoe are bent. Therefore, if possible, try to make the tools yourself.
Take:
- stalk;
- fragment of a water pipe;
- trim from a two-handed saw;
- screws;
- screws;
- a fragment of a profile pipe with a cross section of 3 cm.
Using a grinder, cut a piece of pipe. Taking a lever tool, you need to cut out a piece of pipe, unbend the sector and in the place where the handle will be, you need to work with a hammer to give the future hoe the desired shape.
To make a blade, take a piece of a two-handed saw and sketch out the outlines of the future hoe. Punch two holes.
At the same distance and the same diameter, you need to make 2 holes on the hoe itself, and then cut out a fragment from a two-handed saw.
Drill these holes with a drill and drill designed for metalworking. Connect the two parts with rivets, which are screws.
Now drill a hole in the top of the hoe so you can attach the handle here.
Make also a scoop, which is very interesting to work in the beds. Then such homemade products for giving will allow you to find a very durable set of tools.
Saw off the desired piece of the cutting with a grinder and begin to unbend part of it with a chisel.
Then, using the lever tools, unbend this part almost completely.
It remains to work with a hammer so that the scoop blade takes the desired shape. Using a felt-tip pen, draw the outlines of its working part and cut it out with a grinder.
Use an abrasive wheel to smooth out the edges of the shovel and make them smoother. Now sand the tool with a flap wheel. This shovel will become so shiny.
Also drill a hole in it for the handle, then insert it and secure with a screw.
Cover the cuttings of both tools with antiseptic and then varnish. Now you can use the tools as intended. If you want, use the same principle to make a ripper for the beds.
It is very exciting to create such things for a summer residence with your own hands. Maybe after you make your tools, you want to make a fixture that can dry part of the harvest. See how one gardener did it.
How to make a dryer for fruits and vegetables?
See what materials you need to take for this:
- sheet metal;
- square pipes;
- locking mechanism;
- polycarbonate sheet;
- self-tapping screws, screws;
- 2 door hinges.
But what tools you need to arm yourself with:
- grinder;
- welding machine;
- drill;
- a clerical knife;
- tape measure and marker;
- scissors for metal;
- hacksaw.
First you need to make the base for the drying cabinet. Make a square tube frame. The horizontal and vertical posts are sawn off so that the edges are straight. And the tips on the connectors should be chamfered.
The door here will be metal. To make it, cut 4 fragments from the iron pipe and weld them into a rectangle. Then you need to sheathe this base with metal using screws with nuts and self-tapping screws. If possible, weld on the steel sheet. To make a baking tray holder, attach wooden blocks to the back of the frame. Take self-tapping screws for this. In this case, on each side there are 4 pieces of wood for 4 trays.
An absorber is installed in the dryer. Take sheets of metal and paint it black. Use heat resistant paint. When it's dry, place this blank on the bottom of the dryer.
For the absorber, take a thick aluminum or copper sheet, or at least steel. These materials conduct heat well. Now you need to sheathe the outside of the dryer, make the roof transparent, made of polycarbonate. Then the sun's rays will penetrate here well. Glass can also be used. Cover the ventilation windows with a mosquito net to keep insects out.
Attach the hinges and locking mechanism to the door. Reattach the door in place. Look, what a wonderful beautiful and spacious dryer turned out to be.
It remains to make baking sheets. They must be breathable. First, put together the frames from the bars, and then attach the metal mesh to them.
Now you can slice the fruit and watch your device work. Place a thermometer in the dryer to keep track of the temperature. It should be in the range of 50–55 ° С. If the temperature is colder, cover the bottom holes with a rag.
In such a homemade dryer, you can dry not only fruits, but also vegetables, spicy herbs, fish, meat, roots. If this diagram of the device of such a device seemed complicated to you, then you can make a dryer from a metal barrel. A hole for the door is cut out in it, and racks made of metal mesh are inserted inside.
So that water does not flow here and there is better ventilation, such a roof is installed on top.
You can upgrade this fixture by installing a fan and an electric heater inside.
If you want to make your own lawn mower, then this is also possible.
Turn an old washing machine into it, for example, this one.
And if you still have an old bedside table, then you will make a platform out of it for the future almost self-propelled device. But you only need a door from the bedside table.
Drill holes in the center of the motor shaft. Make a cutting knife from an old two-handed saw. It is necessary to saw off from it to the size of the desired shape, cut out a recess inside.
To make the lawn mower easy to transport, take the wheels from the same old washing machine. They will become the rear wheels of the mower.
And you can take the front ones from a baby stroller.
In order not to bump into fences and other obstacles with a knife when mowing, place the front wheels so that they protrude slightly behind the knife.
Cover the electric motor with a cover cut from a plastic container.
Attach two wooden pickets that will become the handles of the mower. Remember to secure the motor and extension cord to it. Now you can test such an interesting unit.
If you are interested in other homemade products for giving, then it will be useful for you to watch the following video.
A lot of interesting ideas await you in the first video.
And you can get acquainted with cool homemade plastic pipes if you watch the second plot.